[FUG-BR] Motherboard Intel S5500BCR re-iniciando no FreeBSD 8.2
Marcelo Gondim
gondim em linuxinfo.com.br
Sexta Junho 24 09:37:08 BRT 2011
Em 24/06/2011 09:11, Cleber L. Medina escreveu:
> Ola,
>
> Não se vc ja fez mas tente desabilitar o ACPI.
>
> Cleber Medina
Opa Cleber,
Tentei desabilitar mas aí o sistema trava no meio do boot.
Coisa muito esquisita mesmo. Alguma coisa que essa Intel testa em alguns
momentos e quando não tem resposta ela simplesmente desliga apitando
várias vezes e depois re-liga.
E por que só com o FreeBSD? Provavelmente alguma coisa que ela espera
uma resposta do SO e quando não tem ela desliga em algum momento.
>
> Em 24/06/2011 08:48, Marcelo Gondim escreveu:
>> Opa Paulo,
>>
>> Peguei o equipamento ontem e nada. Não consegui resolver ainda. Mesmo
>> com o FreeBSD 8.2-STABLE o equipamento se auto desliga randomicamente.
>> Abaixo o dmesg dela:
>>
>> Copyright (c) 1992-2011 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>> The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 8.2-STABLE #0: Thu Jun 23 04:13:40 BRT 2011
>> root em zeus.linuxinfo.com.br:/usr/obj/usr/src/sys/GONDIM amd64
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> CPU: Intel(R) Xeon(R) CPU E5606 @ 2.13GHz (2133.32-MHz
>> K8-class CPU)
>> Origin = "GenuineIntel" Id = 0x206c2 Family = 6 Model = 2c
>> Stepping = 2
>>
>> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>>
>> Features2=0x29ee3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,DCA,SSE4.1,SSE4.2,POPCNT,AESNI>
>> AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
>> AMD Features2=0x1<LAHF>
>> TSC: P-state invariant
>> real memory = 8589934592 (8192 MB)
>> avail memory = 8150536192 (7772 MB)
>> ACPI APIC Table:<INTEL S5500BC>
>> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
>> FreeBSD/SMP: 2 package(s) x 4 core(s)
>> cpu0 (BSP): APIC ID: 0
>> cpu1 (AP): APIC ID: 2
>> cpu2 (AP): APIC ID: 18
>> cpu3 (AP): APIC ID: 20
>> cpu4 (AP): APIC ID: 32
>> cpu5 (AP): APIC ID: 34
>> cpu6 (AP): APIC ID: 50
>> cpu7 (AP): APIC ID: 52
>> ioapic0<Version 2.0> irqs 0-23 on motherboard
>> ioapic1<Version 2.0> irqs 24-47 on motherboard
>> lapic0: Forcing LINT1 to edge trigger
>> kbd1 at kbdmux0
>> cryptosoft0:<software crypto> on motherboard
>> acpi0:<INTEL S5500BC> on motherboard
>> acpi0: [ITHREAD]
>> acpi0: Power Button (fixed)
>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
>> acpi_timer0:<24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
>> cpu0:<ACPI CPU> on acpi0
>> cpu1:<ACPI CPU> on acpi0
>> cpu2:<ACPI CPU> on acpi0
>> cpu3:<ACPI CPU> on acpi0
>> cpu4:<ACPI CPU> on acpi0
>> cpu5:<ACPI CPU> on acpi0
>> cpu6:<ACPI CPU> on acpi0
>> cpu7:<ACPI CPU> on acpi0
>> pcib0:<ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>> pci0:<ACPI PCI bus> on pcib0
>> pcib1:<ACPI PCI-PCI bridge> irq 28 at device 1.0 on pci0
>> pci1:<ACPI PCI bus> on pcib1
>> em0:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0x1000-0x101f mem
>> 0xb1a00000-0xb1a1ffff,0xb1900000-0xb19fffff,0xb1a20000-0xb1a23fff irq 28
>> at device 0.0 on pci1
>> em0: Using MSIX interrupts with 3 vectors
>> em0: [ITHREAD]
>> em0: [ITHREAD]
>> em0: [ITHREAD]
>> em0: Ethernet address: 00:1e:67:07:9d:cd
>> pcib2:<ACPI PCI-PCI bridge> irq 24 at device 3.0 on pci0
>> pci2:<ACPI PCI bus> on pcib2
>> pcib3:<ACPI PCI-PCI bridge> irq 30 at device 7.0 on pci0
>> pci3:<ACPI PCI bus> on pcib3
>> pcib4:<ACPI PCI-PCI bridge> irq 32 at device 9.0 on pci0
>> pci4:<ACPI PCI bus> on pcib4
>> pci0:<base peripheral, interrupt controller> at device 16.0 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 16.1 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 17.0 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 17.1 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 20.0 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 20.1 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 20.2 (no driver
>> attached)
>> pci0:<base peripheral, interrupt controller> at device 20.3 (no driver
>> attached)
>> pci0:<base peripheral> at device 22.0 (no driver attached)
>> pci0:<base peripheral> at device 22.1 (no driver attached)
>> pci0:<base peripheral> at device 22.2 (no driver attached)
>> pci0:<base peripheral> at device 22.3 (no driver attached)
>> pci0:<base peripheral> at device 22.4 (no driver attached)
>> pci0:<base peripheral> at device 22.5 (no driver attached)
>> pci0:<base peripheral> at device 22.6 (no driver attached)
>> pci0:<base peripheral> at device 22.7 (no driver attached)
>> em1:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0x20e0-0x20ff mem
>> 0xb1b00000-0xb1b1ffff,0xb1b43000-0xb1b43fff irq 20 at device 25.0 on pci0
>> em1: Using an MSI interrupt
>> em1: [FILTER]
>> em1: Ethernet address: 00:1e:67:07:9d:cc
>> uhci0:<Intel 82801JI (ICH10) USB controller USB-D> port 0x20c0-0x20df
>> irq 19 at device 26.0 on pci0
>> uhci0: [ITHREAD]
>> usbus0:<Intel 82801JI (ICH10) USB controller USB-D> on uhci0
>> uhci1:<Intel 82801JI (ICH10) USB controller USB-E> port 0x20a0-0x20bf
>> irq 19 at device 26.1 on pci0
>> uhci1: [ITHREAD]
>> usbus1:<Intel 82801JI (ICH10) USB controller USB-E> on uhci1
>> uhci2:<Intel 82801JI (ICH10) USB controller USB-F> port 0x2080-0x209f
>> irq 19 at device 26.2 on pci0
>> uhci2: [ITHREAD]
>> usbus2:<Intel 82801JI (ICH10) USB controller USB-F> on uhci2
>> ehci0:<Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem
>> 0xb1b41000-0xb1b413ff irq 19 at device 26.7 on pci0
>> ehci0: [ITHREAD]
>> usbus3: EHCI version 1.0
>> usbus3:<Intel 82801JI (ICH10) USB 2.0 controller USB-B> on ehci0
>> pcib5:<ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
>> pci5:<ACPI PCI bus> on pcib5
>> pcib6:<ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
>> pci6:<ACPI PCI bus> on pcib6
>> vgapci0:<VGA-compatible display> mem
>> 0xb0000000-0xb0ffffff,0xb1800000-0xb1803fff,0xb1000000-0xb17fffff irq 16
>> at device 0.0 on pci6
>> uhci3:<Intel 82801JI (ICH10) USB controller USB-A> port 0x2060-0x207f
>> irq 16 at device 29.0 on pci0
>> uhci3: [ITHREAD]
>> usbus4:<Intel 82801JI (ICH10) USB controller USB-A> on uhci3
>> uhci4:<Intel 82801JI (ICH10) USB controller USB-B> port 0x2040-0x205f
>> irq 16 at device 29.1 on pci0
>> uhci4: [ITHREAD]
>> usbus5:<Intel 82801JI (ICH10) USB controller USB-B> on uhci4
>> uhci5:<Intel 82801JI (ICH10) USB controller USB-C> port 0x2020-0x203f
>> irq 16 at device 29.2 on pci0
>> uhci5: [ITHREAD]
>> usbus6:<Intel 82801JI (ICH10) USB controller USB-C> on uhci5
>> ehci1:<Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem
>> 0xb1b40000-0xb1b403ff irq 16 at device 29.7 on pci0
>> ehci1: [ITHREAD]
>> usbus7: EHCI version 1.0
>> usbus7:<Intel 82801JI (ICH10) USB 2.0 controller USB-A> on ehci1
>> pcib7:<ACPI PCI-PCI bridge> at device 30.0 on pci0
>> pci7:<ACPI PCI bus> on pcib7
>> isab0:<PCI-ISA bridge> at device 31.0 on pci0
>> isa0:<ISA bus> on isab0
>> atapci0:<Intel ICH10 SATA300 controller> port
>> 0x2158-0x215f,0x216c-0x216f,0x2150-0x2157,0x2168-0x216b,0x2130-0x213f,0x2120-0x212f
>> irq 18 at device 31.2 on pci0
>> atapci0: [ITHREAD]
>> ata2:<ATA channel 0> on atapci0
>> ata2: [ITHREAD]
>> ata3:<ATA channel 1> on atapci0
>> ata3: [ITHREAD]
>> pci0:<serial bus, SMBus> at device 31.3 (no driver attached)
>> atapci1:<Intel ICH10 SATA300 controller> port
>> 0x2148-0x214f,0x2164-0x2167,0x2140-0x2147,0x2160-0x2163,0x2110-0x211f,0x2100-0x210f
>> irq 21 at device 31.5 on pci0
>> atapci1: [ITHREAD]
>> ata4:<ATA channel 0> on atapci1
>> ata4: [ITHREAD]
>> ata5:<ATA channel 1> on atapci1
>> ata5: [ITHREAD]
>> acpi_button0:<Sleep Button> on acpi0
>> atrtc0:<AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0
>> acpi_hpet0:<High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
>> acpi0
>> Timecounter "HPET" frequency 14318180 Hz quality 900
>> qpi0:<QPI system bus> on motherboard
>> pcib8:<QPI Host-PCI bridge> pcibus 255 on qpi0
>> pci255:<PCI bus> on pcib8
>> pcib9:<QPI Host-PCI bridge> pcibus 254 on qpi0
>> pci254:<PCI bus> on pcib9
>> orm0:<ISA Option ROMs> at iomem
>> 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc9fff on isa0
>> atkbd: unable to set the command byte.
>> sc0:<System console> at flags 0x100 on isa0
>> sc0: VGA<16 virtual consoles, flags=0x300>
>> vga0:<Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>> atkbdc0:<Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>> atkbd0:<AT Keyboard> irq 1 on atkbdc0
>> kbd0 at atkbd0
>> atkbd0: [GIANT-LOCKED]
>> atkbd0: [ITHREAD]
>> psm0: unable to set the command byte.
>> est0:<Enhanced SpeedStep Frequency Control> on cpu0
>> p4tcc0:<CPU Frequency Thermal Control> on cpu0
>> est1:<Enhanced SpeedStep Frequency Control> on cpu1
>> p4tcc1:<CPU Frequency Thermal Control> on cpu1
>> est2:<Enhanced SpeedStep Frequency Control> on cpu2
>> p4tcc2:<CPU Frequency Thermal Control> on cpu2
>> est3:<Enhanced SpeedStep Frequency Control> on cpu3
>> p4tcc3:<CPU Frequency Thermal Control> on cpu3
>> est4:<Enhanced SpeedStep Frequency Control> on cpu4
>> p4tcc4:<CPU Frequency Thermal Control> on cpu4
>> est5:<Enhanced SpeedStep Frequency Control> on cpu5
>> p4tcc5:<CPU Frequency Thermal Control> on cpu5
>> est6:<Enhanced SpeedStep Frequency Control> on cpu6
>> p4tcc6:<CPU Frequency Thermal Control> on cpu6
>> est7:<Enhanced SpeedStep Frequency Control> on cpu7
>> p4tcc7:<CPU Frequency Thermal Control> on cpu7
>> Timecounters tick every 1.000 msec
>> IPsec: Initialized Security Association Processing.
>> ipfw2 (+ipv6) initialized, divert enabled, nat enabled, rule-based
>> forwarding enabled, default to accept, logging disabled
>> DUMMYNET 0 with IPv6 initialized (100409)
>> load_dn_sched dn_sched FIFO loaded
>> load_dn_sched dn_sched PRIO loaded
>> load_dn_sched dn_sched QFQ loaded
>> load_dn_sched dn_sched RR loaded
>> load_dn_sched dn_sched WF2Q+ loaded
>> usbus0: 12Mbps Full Speed USB v1.0
>> usbus1: 12Mbps Full Speed USB v1.0
>> usbus2: 12Mbps Full Speed USB v1.0
>> usbus3: 480Mbps High Speed USB v2.0
>> usbus4: 12Mbps Full Speed USB v1.0
>> usbus5: 12Mbps Full Speed USB v1.0
>> usbus6: 12Mbps Full Speed USB v1.0
>> usbus7: 480Mbps High Speed USB v2.0
>> ugen0.1:<Intel> at usbus0
>> uhub0:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
>> ugen1.1:<Intel> at usbus1
>> uhub1:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
>> ugen2.1:<Intel> at usbus2
>> uhub2:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
>> ugen3.1:<Intel> at usbus3
>> uhub3:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
>> ugen4.1:<Intel> at usbus4
>> uhub4:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
>> ugen5.1:<Intel> at usbus5
>> uhub5:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
>> ugen6.1:<Intel> at usbus6
>> uhub6:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
>> ugen7.1:<Intel> at usbus7
>> uhub7:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
>> ad4: 953869MB<Seagate ST31000528AS CC44> at ata2-master UDMA100 SATA 3Gb/s
>> acd0: DVDR<HL-DT-ST DVDRAM GH22NS50/TN03> at ata3-master UDMA100 SATA
>> 1.5Gb/s
>> lapic20: Forcing LINT1 to edge trigger
>> SMP: AP CPU #3 Launched!
>> lapic34: Forcing LINT1 to edge trigger
>> SMP: AP CPU #5 Launched!
>> lapic2: Forcing LINT1 to edge trigger
>> SMP: AP CPU #1 Launched!
>> lapic52: Forcing LINT1 to edge trigger
>> SMP: AP CPU #7 Launched!
>> lapic18: Forcing LINT1 to edge trigger
>> SMP: AP CPU #2 Launched!
>> lapic32: Forcing LINT1 to edge trigger
>> SMP: AP CPU #4 Launched!
>> lapic50: Forcing LINT1 to edge trigger
>> SMP: AP CPU #6 Launched!
>> Root mount waiting for: usbus7 usbus6 usbus5 usbus4 usbus3 usbus2 usbus1
>> usbus0
>> uhub0: 2 ports with 2 removable, self powered
>> uhub1: 2 ports with 2 removable, self powered
>> uhub2: 2 ports with 2 removable, self powered
>> uhub4: 2 ports with 2 removable, self powered
>> uhub5: 2 ports with 2 removable, self powered
>> uhub6: 2 ports with 2 removable, self powered
>> Root mount waiting for: usbus7 usbus3
>> Root mount waiting for: usbus7 usbus3
>> uhub3: 6 ports with 6 removable, self powered
>> uhub7: 6 ports with 6 removable, self powered
>> Trying to mount root from ufs:/dev/ad4s1a
>> WARNING: / was not properly dismounted
>> ugen0.2:<CHESEN> at usbus0
>> ukbd0:<CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on usbus0
>> kbd2 at ukbd0
>> uhid0:<CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on usbus0
>> ugen2.2:<American Megatrends Inc.> at usbus2
>> ukbd1:<Keyboard Interface> on usbus2
>> kbd3 at ukbd1
>> ums0:<Mouse Interface> on usbus2
>> ums0: 3 buttons and [Z] coordinates ID=0
>> WARNING: /tmp was not properly dismounted
>> WARNING: /usr was not properly dismounted
>> WARNING: /var was not properly dismounted
>> em0: link state changed to UP
>>
>> Esses warning é porque ela desliga do nada e aí obviamente lá vai um
>> fsck e pior que demora pacas porque o disco é de 1Tb.
>>
>> Em 17/06/2011 17:32, Paulo Henrique - BSDs Brasil escreveu:
>>> Tem algum dmesg para poder ver o que a placa-mãe possui.
>>> NO site da intel a descrićão é muito resumida, o que diz que ela possui
>>> o que de fato o FreeBSD suporta, não sei quanto IPMI2.0.
>>> Att.
>>> Marcelo Gondim wrote:
>>>> Em 17/06/2011 15:21, Paulo Henrique - BSDs Brasil escreveu:
>>>>
>>>>> Inicia o FreeBSD em modo debug e manda a saida para nós.
>>>>> Informaćão quanto ao solucionamento importantissima para a lista.
>>>>>
>>>>> Att.
>>>>>
>>>>>
>>>> Opa Paulo,
>>>>
>>>> Vou tentar mas o problema dá randomicamente. O sistema inicia normal,
>>>> fica lá no login tranqüilo e do nada desliga e liga.
>>>> Mas com certeza descobrindo uma solução estarei postando aqui. O
>>>> equipamento está agora em um laboratório no Rio em testes para
>>>> descobrirmos o motivo ou pelo menos tentarmos.
>>>>
>>>>
>>>>> Marcelo Gondim wrote:
>>>>>
>>>>>> Olá pessoal,
>>>>>>
>>>>>> Comprei um equipamento dual Quad Xeon e esse usa uma motherboard
>>>>>> S5500BCR que é dual processada. O que ocorre é o seguinte:
>>>>>>
>>>>>> Na instalação do FreeBSD 8.2-release a máquina simplesmente desliga dá
>>>>>> uns apitos indicando problema e re-inicia novamente sozinha. Consegui
>>>>>> com muito custo terminar a instalação do sistema mas não estou
>>>>>> conseguindo atualizar para a versão 8.2-stable porque ela sempre
>>>>>> re-inicia antes mesmo de eu completar. Sei que muitos vão achar que é um
>>>>>> problema no hardware ou elétrica, também achei isso e troquei fonte,
>>>>>> memória, processador e até a motherboard e nada resolveu. Testei com
>>>>>> outros sistemas como windows 2008 e linux e o problema não ocorre mas
>>>>>> com o FreeBSD está acontecendo isso. Alguém faz idéia do que seja?
>>>>>> Porque procurei nos logs e não vi nada, dmesg também nada.
>>>>>> Estou pensando em tirar o hd, colocar em outro equipamento, atualizar
>>>>>> para a 8.2-stable e colocar de volta para ver se acontece o mesmo problema.
>>>>>>
>>>>>> Alguém passou por esse pepino?
>>>>>>
>>>>>> []´s
>>>>>>
>>>>>> Gondim
>>>>>> -------------------------
>>>>>> Histórico:http://www.fug.com.br/historico/html/freebsd/
>>>>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd
>>>>>>
>>>>>>
>>>>> -------------------------
>>>>> Histórico:http://www.fug.com.br/historico/html/freebsd/
>>>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd
>>>>>
>>>> -------------------------
>>>> Histórico:http://www.fug.com.br/historico/html/freebsd/
>>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd
>>>>
>>> -------------------------
>>> Histórico:http://www.fug.com.br/historico/html/freebsd/
>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd
>> -------------------------
>> Histórico:http://www.fug.com.br/historico/html/freebsd/
>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd
> -------------------------
> Histórico: http://www.fug.com.br/historico/html/freebsd/
> Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd
Mais detalhes sobre a lista de discussão freebsd