[FUGSPBR] erro ao compilar o kernel

Qua Jan 9 16:05:18 BRST 2002

Olá Alexandre,

conforme está no site www.free.bsd.com.br

# cd /usr/src/sys/i386/conf
# cp GENERIC SEUKERNEL
# pico SEUKERNEL  # configura as opcoes do seu kernel
# config SEUKERNEL
# cd ../../compile/SEUKERNEL
# make depend
# make
# make install
# fastboot

é só para rodar nat, firewall mais nada... bem simplizinhu

a maquina é k6/266 128 ram e 2.1 hd formatado conforme instruções do vinis

meu kernel

machine i386
cpu I386_CPU
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident GENERIC
maxusers 32

#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols

options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev

# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O

device isa
device eisa
device pci

# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1

# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices

# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device amd # AMD 53C974 (Teckram DC-390(T))
device isp # Qlogic family
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured

device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?

device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50

# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)

# RAID controllers interfaced to the SCSI subsystem
device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
device dpt # DPT Smartcache - See LINT for options!
device mly # Mylex AcceleRAID/eXtremeRAID

# RAID controllers
device ida # Compaq Smart RAID
device amr # AMI MegaRAID
device mlx # Mylex DAC960 family
device twe # 3ware Escalade

# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12

device vga0 at isa?

# splash screen/screen saver
pseudo-device splash

# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100

# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std

# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13

# Power management support (see LINT for more options)
device apm0    at nexus? disable flags 0x20 # Advanced Power Management

# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable

# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9

# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da

# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
device wx # Intel Gigabit Ethernet Card (``Wiseman'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device pcn # AMD Am79C79x PCI 10/100 NICs
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')

# ISA Ethernet NICs.
device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? port 0x300
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
device an
# Xircom Ethernet
device xe
# The probe order of these is presently determined by i386/isa/isa_compat.c.
device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 irq 10 drq 0
device cs0 at isa? port 0x300
device sn0 at isa? port 0x300 irq 10

# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)

# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter

# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet

#NAT options

options IPFIREWALL
options IPFILTER
options IPDIVERT
options IPFIREWALL_FORWARD
options IPFIREWALL_DEFAULT_TO_ACCEPT

----- Original Message -----
From: "Alexandre Mioranza" <alexandre.mioranza em varig.com>
To: <fugspbr em fugspbr.org>
Sent: Wednesday, January 09, 2002 3:56 PM
Subject: Re: [FUGSPBR] erro ao compilar o kernel

> Envia a config do seu kernel para a lista, de repennte é algum problema
com o arquivo de configuração. Outra coisa como vc está fazendo para
recompilar o kernel?
>
> On Wed, 9 Jan 2002 15:45:38 -0200
> "Fabricio" <fabricio em eureca.com.br> wrote:
>
> > Fala ae povo
> >
> >
> >
> > estou tentando recompilar o kernel do 4.4 Release jah tentei de tudo..
nao
> > instalava por cd instalei por ftp
> >
> > quando vou recompilar aparece isso
> >
> >
> > Parou no /usr/src/modules/twe
> >
> >
> > Bus error - core dumped
> > *** Error code 138
> >
> > Stop in /usr/src/sys/modules
> > *** Error code 1
> >
> >
> >
> >
> > ----
> > Para sair da lista envie um e-mail para majordomo em fugspbr.org
> > com as palavras "unsubscribe fugspbr" no corpo da mensagem.
>
>
> _______________________________________
>           __      ___ ___
>         /'__`\  /' __` __`\
>        /\ \_\.\_/\ \/\ \/\ \
>        \ \__/.\_\ \_\ \_\ \_\
>         \/__/\/_/\/_/\/_/\/_/
>
>           Alexandre Mioranza
>      VARIG Engenharia & Manutenção
>            Sistemas e Métodos
>  email: alexandre.mioranza em varig.com.br
>  ______________________________________
> ----
> Para sair da lista envie um e-mail para majordomo em fugspbr.org
> com as palavras "unsubscribe fugspbr" no corpo da mensagem.
>
>

----
Para sair da lista envie um e-mail para majordomo em fugspbr.org
com as palavras "unsubscribe fugspbr" no corpo da mensagem.