[FUGSPBR] Configurar o printcap para impressora Hp1200 laser
Rogerio Heringer
rogerio em aeronet.com.br
Sex Maio 30 13:13:00 BRT 2003
ok
consegui imprimir.
agora estou tentando por para imprimir no samba
o q de especial preciso ter no smb.conf ?
[]'s
Rogerio Heringer
----- Original Message -----
From: "Rogerio Heringer" <rogerio em aeronet.com.br>
To: "Grupo Brasileiro de Usuarios FreeBSD" <fugspbr em fugspbr.org>
Sent: Friday, May 30, 2003 12:55 PM
Subject: [FUGSPBR] Configurar o printcap para impressora Hp1200 laser
> Estou com dificuldades de fazer imprimir num freebsd 4.7 , impressora
hp1200
> laser.
> olhem o meu printcap:
>
> #laserjet|ps|PS|S|laserjet|Hp LaserJet 1200 :\
> # :sh:sd=/var/spool/lpd/laserjet:\
> # :lp=/dev/lpt0:
> lp|local line printer:\
> :sh:\
> :lp=/dev/lpt0:sd=/var/spool/output/lpd:lf=/var/log/lpd-errs:
> ja tentei das 2 formas
>
> com o lp e com o laserjet.
> e com os 2 simultaneamente.
> ja criei os diretorios
> /var/spool/lpd/laserjet
> /var/spool/lpd/lp
> ja dei permissao 777 neles..
> ta rodando o lpd...
>
> o meu dmsg ta assim:
>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 8250
> sio1: configured irq 3 not in bitmap of probed irqs 0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: IEEE1284 device found /NIBBLE/ECP
> Probing for PnP devices on ppbus0:
> ppbus0: <Hewlett-Packard HP LaserJet 1200> PRINTER
> PJL,MLC,PCL,PCLXL,POSTSCRIPT
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> IP packet filtering initialized, divert enabled, rule-based forwarding
> enabled,
> default to accept, logging disabled
> DUMMYNET initialized (011031)
> da0 at ahc0 bus 0 target 1 lun 0
> da0: <QUANTUM ATLAS_V__9_WLS 0230> Fixed Direct Access SCSI-3 device
> da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
> da0: 8755MB (17930694 512 byte sectors: 255H 63S/T 1116C)
> da1 at ahc0 bus 0 target 2 lun 0
> da1: <SEAGATE ST39236LW 0004> Fixed Direct Access SCSI-3 device
> da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
> da1: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
> Mounting root from ufs:/dev/da0s1a
> lpt0: switched to polled standard mode
>
>
> alguem tem ideia do que seja??
>
> um abraco
>
> Rogerio Heringer
>
> _______________________________________________________________
> Sair da Lista: http://www2.fugspbr.org/mailman/listinfo/fugspbr
> Historico: http://www4.fugspbr.org/lista/html/FUG-BR/
>
_______________________________________________________________
Sair da Lista: http://www2.fugspbr.org/mailman/listinfo/fugspbr
Historico: http://www4.fugspbr.org/lista/html/FUG-BR/
Mais detalhes sobre a lista de discussão freebsd