[FUGSPBR] Configurar o printcap para impressora Hp1200 laser

[Luiz Morte]

Rogerio,

Da uma olhada no programa apsfilter e ve se te ajuda. Ele esta no ports.
www.apsfilter.org

[]s,
Luiz Morte.



----- Original Message ----- 
From: "Rogerio Heringer" <rogerio em aeronet.com.br>
To: "Grupo Brasileiro de Usuarios FreeBSD" <fugspbr em fugspbr.org>
Sent: Friday, May 30, 2003 1:13 PM
Subject: Re: [FUGSPBR] Configurar o printcap para impressora Hp1200 laser


> ok
> consegui imprimir.
> agora estou tentando por  para imprimir no samba
> o q de especial preciso ter no smb.conf ?
> 
> 
> []'s
> 
> Rogerio Heringer
> 
> 
> 
> 
> 
> ----- Original Message ----- 
> From: "Rogerio Heringer" <rogerio em aeronet.com.br>
> To: "Grupo Brasileiro de Usuarios FreeBSD" <fugspbr em fugspbr.org>
> Sent: Friday, May 30, 2003 12:55 PM
> Subject: [FUGSPBR] Configurar o printcap para impressora Hp1200 laser
> 
> 
> > Estou com dificuldades de fazer imprimir num freebsd 4.7 , impressora
> hp1200
> > laser.
> > olhem o meu printcap:
> >
> > #laserjet|ps|PS|S|laserjet|Hp LaserJet 1200 :\
> > #        :sh:sd=/var/spool/lpd/laserjet:\
> > #        :lp=/dev/lpt0:
> > lp|local line printer:\
> >         :sh:\
> >         :lp=/dev/lpt0:sd=/var/spool/output/lpd:lf=/var/log/lpd-errs:
> > ja tentei das 2 formas
> >
> > com o lp e com o laserjet.
> > e com os 2 simultaneamente.
> > ja criei os diretorios
> > /var/spool/lpd/laserjet
> > /var/spool/lpd/lp
> > ja dei permissao 777 neles..
> > ta rodando o lpd...
> >
> > o meu dmsg ta assim:
> >
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 8250
> > sio1: configured irq 3 not in bitmap of probed irqs 0
> > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> > ppbus0: IEEE1284 device found /NIBBLE/ECP
> > Probing for PnP devices on ppbus0:
> > ppbus0: <Hewlett-Packard HP LaserJet 1200> PRINTER
> > PJL,MLC,PCL,PCLXL,POSTSCRIPT
> > plip0: <PLIP network interface> on ppbus0
> > lpt0: <Printer> on ppbus0
> > lpt0: Interrupt-driven port
> > ppi0: <Parallel I/O> on ppbus0
> > IP packet filtering initialized, divert enabled, rule-based forwarding
> > enabled,
> > default to accept, logging disabled
> > DUMMYNET initialized (011031)
> > da0 at ahc0 bus 0 target 1 lun 0
> > da0: <QUANTUM ATLAS_V__9_WLS 0230> Fixed Direct Access SCSI-3 device
> > da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
> > da0: 8755MB (17930694 512 byte sectors: 255H 63S/T 1116C)
> > da1 at ahc0 bus 0 target 2 lun 0
> > da1: <SEAGATE ST39236LW 0004> Fixed Direct Access SCSI-3 device
> > da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
> > da1: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
> > Mounting root from ufs:/dev/da0s1a
> > lpt0: switched to polled standard mode
> >
> >
> > alguem tem ideia do que seja??
> >
> > um abraco
> >
> > Rogerio Heringer
> >
> > _______________________________________________________________
> > Sair da Lista: http://www2.fugspbr.org/mailman/listinfo/fugspbr
> > Historico: http://www4.fugspbr.org/lista/html/FUG-BR/
> >
> 
> _______________________________________________________________
> Sair da Lista: http://www2.fugspbr.org/mailman/listinfo/fugspbr
> Historico: http://www4.fugspbr.org/lista/html/FUG-BR/
> 
_______________________________________________________________
Sair da Lista: http://www2.fugspbr.org/mailman/listinfo/fugspbr
Historico: http://www4.fugspbr.org/lista/html/FUG-BR/