[FUG-BR] Ajuda com Storage (HBA Qlogic 2312)
Mauro Felipe
maurofelipe em gmail.com
Qui Maio 4 12:26:39 BRT 2006
2006/5/4, Marcus Alves Grando <marcus em corp.grupos.com.br>:
>
> Muito estranho... Se está criado o volume e esta associado com o seu
> servidor teria que reconhecer. Verifica no storage se está tudo correto
> mesmo, pois eu ainda acho que não está associado a sua placa em algum
> volume criado.
>
>
Marcos, você estava correto! Era realmente problema no próprio Storage, eu
refiz as conexões e agora está funcionando! Eu consigo ver as unidades da1 e
da2 conforme o DMESG, mas agora também está mostrando um erro:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE-p7 #0: Wed May 3 15:02:04 BRT 2006
root em faraday.mct.gov.br:/usr/src/sys/i386/compile/FARADAY
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 3.06GHz (3048.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,P
AT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4400<CNTX-ID,<b14>>
Hyperthreading: 2 logical CPUs
real memory = 1073717248 (1023 MB)
avail memory = 1041653760 (993 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <COMPAQ P29> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link IUSB> on acpi0
pci_link1: <ACPI PCI Link IN16> on acpi0
pci_link2: <ACPI PCI Link IN17> on acpi0
pci_link3: <ACPI PCI Link IN18> on acpi0
pci_link4: <ACPI PCI Link IN19> on acpi0
pci_link5: <ACPI PCI Link IN20> on acpi0
pci_link6: <ACPI PCI Link IN21> on acpi0
pci_link7: <ACPI PCI Link IN22> on acpi0
pci_link8: <ACPI PCI Link IN23> on acpi0
pci_link9: <ACPI PCI Link IN24> on acpi0
pci_link10: <ACPI PCI Link IN25> on acpi0
pci_link11: <ACPI PCI Link IN26> on acpi0
pci_link12: <ACPI PCI Link IN27> on acpi0
pci_link13: <ACPI PCI Link IN28> on acpi0
pci_link14: <ACPI PCI Link IN29> on acpi0
pci_link15: <ACPI PCI Link IN30> on acpi0
pci_link16: <ACPI PCI Link IN31> on acpi0
pci_link17: <ACPI PCI Link IN32> on acpi0
pci_link18: <ACPI PCI Link IN33> on acpi0
pci_link19: <ACPI PCI Link IN34> on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 3.0 (no driver attached)
pci0: <base peripheral> at device 4.0 (no driver attached)
pci0: <base peripheral> at device 4.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x17
7,0x376,0x2000-0x200f at device 15.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xf5ef0000-0xf5ef0fff irq 7 at
device 15.2 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem
0xf7bc0000-0xf7bfffff,0xf7
af0000-0xf7af3fff irq 10 at device 3.0 on pci1
ciss0: [GIANT-LOCKED]
pcib2: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xf7cf0000-0xf7c fffff irq 11
at device 1.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX -FDX, auto
bge0: Ethernet address: 00:0e:7f:21:61:37
bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xf7ce0000-0xf7c effff irq 15
at device 2.0 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX -FDX, auto
bge1: Ethernet address: 00:0e:7f:21:61:36
pcib3: <ACPI Host-PCI bridge> on acpi0
pci3: <ACPI PCI bus> on pcib3
isp0: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x4000-0x40ff mem
0xf7df0000-0xf7 df0fff irq 15
at device 1.0 on pci3
isp0: [GIANT-LOCKED]
isp0: Board Type 2312, Chip Revision 0x2, loaded F/W Revision 3.3.6
isp0: Installed in 64-Bit PCI slot
isp0: 839 max I/O commands supported
isp0: NVRAM Port WWN 0x210000e08b11c60d
pcib4: <ACPI Host-PCI bridge> on acpi0
pci6: <ACPI PCI bus> on pcib4
isp1: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x5000-0x50ff mem
0xf7ff0000-0xf7 ff0fff irq 11
at device 1.0 on pci6
isp1: [GIANT-LOCKED]
bge2: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xf7fe0000-0xf7fe ffff irq 7 at
device 2.0 on pci6
bge2: Ethernet address: 00:08:02:28:4a:b9
pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no driver
attac hed)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xee000-0xeffff
on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 3048830952 Hz quality 800
Timecounters tick every 1.000 msec
isp0: Point-to-Point mode
isp0: Loop UP
isp0: Port Database Changed
isp0: Port Database Changed
isp0: Firmware State <Config Wait->Ready>
isp0: Target 126 (Loop 0x7e) Port ID 0xfffffe (role (none)) Arrived
Port WWN 0x2008006069517c7c
Node WWN 0x1000006069517c7c
isp0: 2Gb link speed/s
isp0: Loop ID 255, AL_PA 0x0, Port ID 0x10800, Loop State 0x2, Topology 'F
Port'
isp0: Target 255 (Loop 0xff) Port ID 0x10800 (role Initiator) Arrived
Port WWN 0x210000e08b11c60d
Node WWN 0x200000e08b11c60d
isp0: Fabric Device @ PortID 0x10f00
isp0: Fabric Device @ PortID 0x10700
isp0: Fabric Device @ PortID 0x10800
isp0: Target 0 (Loop 0x1) Port ID 0x10f00 (role Target) Arrived
Port WWN 0x500805f3000ba4a9
Node WWN 0x500805f3000ba4a0
isp0: Target 1 (Loop 0x2) Port ID 0x10700 (role Initiator) Arrived
Port WWN 0x210000e08b119312
Node WWN 0x200000e08b119312
acd0: CDRW <DW-224E/A.1K> at ata0-master PIO4
pass1 at isp0 bus 0 target 0 lun 0
pass1: <COMPAQ MSA1000 4.32> Fixed Storage Array SCSI-4 device
pass1: 200.000MB/s transfers, Tagged Queueing Enabled
pass3 at isp1 bus 0 target 0 lun 0
pass3: <COMPAQ MSA1000 4.32> Fixed Storage Array SCSI-4 device
pass3: 200.000MB/s transfers, Tagged Queueing Enabled
da2 at isp1 bus 0 target 0 lun 5
da2: <COMPAQ MSA1000 VOLUME 4.32> Fixed Direct Access SCSI-4 device
da2: 200.000MB/s transfers, Tagged Queueing Enabled
da2: 99999MB (204799680 512 byte sectors: 255H 63S/T 12748C)
da1 at isp0 bus 0 target 0 lun 5
da1: <COMPAQ MSA1000 VOLUME 4.32> Fixed Direct Access SCSI-4 device
da1: 200.000MB/s transfers, Tagged Queueing Enabled
da1: 99999MB (204799680 512 byte sectors: 255H 63S/T 12748C)
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 69455MB (142245120 512 byte sectors: 255H 32S/T 17432C)
(da2:isp1:0:0:5): READ(6)/WRITE(6) not supported, increasing
minimum_cmd_size to 10.
(da2:isp1:0:0:5): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0
(da2:isp1:0:0:5): CAM Status: SCSI Status Error
(da2:isp1:0:0:5): SCSI Status: Check Condition
(da2:isp1:0:0:5): ILLEGAL REQUEST asc:20,0
(da2:isp1:0:0:5): Invalid command operation code
(da2:isp1:0:0:5): Unretryable error
(da2:isp1:0:0:5): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0
(da2:isp1:0:0:5): CAM Status: SCSI Status Error
(da2:isp1:0:0:5): SCSI Status: Check Condition
(da2:isp1:0:0:5): ILLEGAL REQUEST asc:20,0
(da2:isp1:0:0:5): Invalid command operation code
(da2:isp1:0:0:5): Unretryable error
(da2:isp1:0:0:5): READ(10). CDB: 28 0 0 0 0 0 0 0 2 0
(da2:isp1:0:0:5): CAM Status: SCSI Status Error
(da2:isp1:0:0:5): SCSI Status: Check Condition
(da2:isp1:0:0:5): ILLEGAL REQUEST asc:20,0
(da2:isp1:0:0:5): Invalid command operation code
(da2:isp1:0:0:5): Unretryable error
(da2:isp1:0:0:5): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0
(da2:isp1:0:0:5): CAM Status: SCSI Status Error
(da2:isp1:0:0:5): SCSI Status: Check Condition
(da2:isp1:0:0:5): ILLEGAL REQUEST asc:20,0
(da2:isp1:0:0:5): Invalid command operation code
(da2:isp1:0:0:5): Unretryable error
Trying to mount root from ufs:/dev/da0s1a
No camcontrol:
<COMPAQ RAID 5 VOLUME OK> at scbus0 target 0 lun 0 (pass0,da0)
<COMPAQ MSA1000 4.32> at scbus3 target 0 lun 0 (pass1)
<COMPAQ MSA1000 VOLUME 4.32> at scbus3 target 0 lun 5 (pass2,da1)
<COMPAQ MSA1000 4.32> at scbus4 target 0 lun 0 (pass3)
<COMPAQ MSA1000 VOLUME 4.32> at scbus4 target 0 lun 5 (pass4,da2)
O que pode ser esse erro acima no DMESG.
--
[ ]´s
Mauro Felipe
-------------- Próxima Parte ----------
Um anexo em HTML foi limpo...
URL: <http://www.fug.com.br/pipermail/freebsd/attachments/20060504/d8082ca2/attachment-0004.html>
Mais detalhes sobre a lista de discussão freebsd