[FUG-BR] RES: Testar RAID 1 no FreebSD 7
Ricardo Augusto de Souza
ricardo.souza em cmtsp.com.br
Quinta Maio 7 20:46:08 BRT 2009
O meu não mostrou NADA no messages e nem dmesg -a
-----Mensagem original-----
De: freebsd-bounces em fug.com.br [mailto:freebsd-bounces em fug.com.br] Em nome de Ari Arantes Filho
Enviada em: quinta-feira, 7 de maio de 2009 20:13
Para: Lista Brasileira de Discussão sobre FreeBSD (FUG-BR)
Assunto: Re: [FUG-BR] Testar RAID 1 no FreebSD 7
Em todas IBM 3550 e 3650 que temos, estamos usando o FreeBSD 7.0, pois em 3
casos, com o 7.1, tivemos travamos frequentes. Foi fazer downgrade p/ 7.0 e
nunca mais travou.
Sobre o RAID 1, quando vc tira o HD, na console mostra uma mensagem de erro
na controladora. Quando coloca, mostra também mensagem de rebuild. Vai pro
/var/log/messages, mas se digitar "dmesg -a" também mostra.
[]s,
Ari
2009/5/7 Ricardo Augusto de Souza <ricardo.souza em cmtsp.com.br>
> Tenho 2 IBM 3550 com FreeBSD 7.1 + carp + pfsync.
> Ambos possuem RAID 1 por hardware com 2 discos SAS.
> acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-T10N/1.00> at ata0-master UDMA33
> aacd0: <RAID 1 (Mirror)> on aac0
> aacd0: 152490MB (312299520 sectors)
>
> EU preciso testar se o RAID esta Ok. Não achei muita documentação na net
> sobre isso.
> Alguem pode me ajudar?
>
> Ontem eu tirei um dos HDs com a maquina ligada e coloquei novamente.
> O consumo de CPU da maquina não mudou. A luz do disco começou a piscar,
> parecia que esta fazendo um rebuild.
>
> Quais testes me sugerem fazer para verificar esta pendência.
>
> Dmesg:
> Copyright (c) 1992-2009 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.1-RELEASE-p3 #1: Thu Apr 16 19:27:25 BRT 2009
> ricardo em Trinity.cmtsp.com.br:/usr/obj/usr/src/sys/CMT
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU E5405 @ 2.00GHz (1995.01-MHz 686-class
> CPU)
> Origin = "GenuineIntel" Id = 0x10676 Stepping = 6
>
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
> Features2=0xce33d<SSE3,DTES64,MON,DS_CPL,VMX,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1>
> AMD Features=0x20000000<LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 4
> real memory = 2147250176 (2047 MB)
> avail memory = 2091597824 (1994 MB)
> ACPI APIC Table: <IBM SERDEFNT>
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> acpi0: <IBM SERDEFNT> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x588-0x58b on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
> acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 900
> pcib0: <ACPI Host-PCI bridge> on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pci16: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci16
> pci17: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci17
> pci19: <ACPI PCI bus> on pcib3
> pcib4: <ACPI PCI-PCI bridge> at device 1.0 on pci17
> pci18: <ACPI PCI bus> on pcib4
> pcib5: <ACPI PCI-PCI bridge> at device 0.3 on pci16
> pci20: <ACPI PCI bus> on pcib5
> pcib6: <PCI-PCI bridge> at device 3.0 on pci0
> pci35: <PCI bus> on pcib6
> pcib7: <ACPI PCI-PCI bridge> at device 4.0 on pci0
> pci7: <ACPI PCI bus> on pcib7
> pcib8: <ACPI PCI-PCI bridge> at device 0.0 on pci7
> pci8: <ACPI PCI bus> on pcib8
> pcib9: <PCI-PCI bridge> at device 0.0 on pci8
> pci9: <PCI bus> on pcib9
> em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x6000-0x601f mem
> 0xc6000000-0xc601ffff,0xc6020000-0xc603ffff irq 19 at device 0.0 on pci9
> em0: Using MSI interrupt
> em0: [FILTER]
> em0: Ethernet address: 00:15:17:7b:be:f0
> em1: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x6020-0x603f mem
> 0xc6040000-0xc605ffff,0xc6060000-0xc607ffff irq 16 at device 0.1 on pci9
> em1: Using MSI interrupt
> em1: [FILTER]
> em1: Ethernet address: 00:15:17:7b:be:f1
> pcib10: <PCI-PCI bridge> at device 1.0 on pci8
> pci10: <PCI bus> on pcib10
> em2: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x5000-0x501f mem
> 0xc4000000-0xc401ffff,0xc4020000-0xc403ffff irq 16 at device 0.0 on pci10
> em2: Using MSI interrupt
> em2: [FILTER]
> em2: Ethernet address: 00:15:17:7b:be:f2
> em3: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x5020-0x503f mem
> 0xc4040000-0xc405ffff,0xc4060000-0xc407ffff irq 17 at device 0.1 on pci10
> em3: Using MSI interrupt
> em3: [FILTER]
> em3: Ethernet address: 00:15:17:7b:be:f3
> pcib11: <PCI-PCI bridge> at device 5.0 on pci0
> pci34: <PCI bus> on pcib11
> pcib12: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pci3: <ACPI PCI bus> on pcib12
> pcib13: <PCI-PCI bridge> at device 0.0 on pci3
> pci4: <PCI bus> on pcib13
> bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
> 0xc8000000-0xc9ffffff irq 18 at device 0.0 on pci4
> miibus0: <MII bus> on bce0
> brgphy0: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bce0: Ethernet address: 00:1a:64:79:1d:c4
> bce0: [ITHREAD]
> bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); F/W
> (0x04000305); Flags( MFW MSI )
> pcib14: <ACPI PCI-PCI bridge> at device 7.0 on pci0
> pci2: <ACPI PCI bus> on pcib14
> aac0: <IBM ServeRAID-8k> port 0x4000-0x40ff mem
> 0xcce00000-0xccffffff,0xcafe0000-0xcaffffff irq 17 at device 0.0 on pci2
> aac0: Enable Raw I/O
> aac0: Enable 64-bit array
> aac0: New comm. interface enabled
> aac0: [ITHREAD]
> aac0: ServeRAID 8k-l , aac driver 2.0.0-1
> pci0: <base peripheral> at device 8.0 (no driver attached)
> pcib15: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci5: <ACPI PCI bus> on pcib15
> pcib16: <PCI-PCI bridge> at device 0.0 on pci5
> pci6: <PCI bus> on pcib16
> bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
> 0xce000000-0xcfffffff irq 16 at device 0.0 on pci6
> miibus1: <MII bus> on bce1
> brgphy1: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bce1: Ethernet address: 00:1a:64:79:1d:c6
> bce1: [ITHREAD]
> bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); F/W
> (0x04000305); Flags( MFW MSI )
> uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port 0x2200-0x221f
> irq 23 at device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> uhci0: [ITHREAD]
> usb0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0
> usb0: USB revision 1.0
> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port 0x2600-0x261f
> irq 22 at device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> uhci1: [ITHREAD]
> usb1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1
> usb1: USB revision 1.0
> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port 0x2a00-0x2a1f
> irq 23 at device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> uhci2: [ITHREAD]
> usb2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2
> usb2: USB revision 1.0
> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
> uhub2: 2 ports with 2 removable, self powered
> ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xf9000000-0xf90003ff irq 23
> at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> ehci0: [ITHREAD]
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <Intel 63XXESB USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
> uhub3: 6 ports with 6 removable, self powered
> pcib17: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci1: <ACPI PCI bus> on pcib17
> vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem
> 0xd0000000-0xd7ffffff,0xdfff0000-0xdfffffff irq 22 at device 1.0 on pci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel 63XXESB2 UDMA100 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x480-0x48f at device 31.1 on pci0
> ata0: <ATA channel 0> on atapci0
> ata0: [ITHREAD]
> ata1: <ATA channel 1> on atapci0
> ata1: [ITHREAD]
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
> acpi0
> sio0: type 16550A
> sio0: [FILTER]
> cpu0: <ACPI CPU> on acpi0
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> cpu1: <ACPI CPU> on acpi0
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> cpu2: <ACPI CPU> on acpi0
> p4tcc2: <CPU Frequency Thermal Control> on cpu2
> cpu3: <ACPI CPU> on acpi0
> p4tcc3: <CPU Frequency Thermal Control> on cpu3
> pmtimer0 on isa0
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xcafff,0xcb000-0xcc7ff,0xcc800-0xcdfff,0xce000-0xd2fff pnpid
> ORM0000 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> ppc0: parallel port not found.
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounters tick every 1.000 msec
> acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-T10N/1.00> at ata0-master UDMA33
> aacd0: <RAID 1 (Mirror)> on aac0
> aacd0: 152490MB (312299520 sectors)
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #3 Launched!
> Trying to mount root from ufs:/dev/aacd0s1a
> WARNING: attempt to net_add_domain(netgraph) after domainfinalize()
> bce0: link state changed to UP
> bce1: link state changed to UP
> em3: link state changed to UP
> arp_rtrequest: bad gateway 200.143.33.139 (!AF_LINK)
> arp_rtrequest: bad gateway 10.100.0.119 (!AF_LINK)
>
> -------------------------
> Histórico: http://www.fug.com.br/historico/html/freebsd/
> Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd
>
-------------------------
Histórico: http://www.fug.com.br/historico/html/freebsd/
Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd
Mais detalhes sobre a lista de discussão freebsd